Featured Clients

Manufactures:

 


 

Decal Installation


     

Pre-cautions before you start.

1. Do not install your vinyl decal in direct sunlight. It is recommended you install your vinyl decal in a garage or building.
2. Room and installation surface temperature is recommended to be 50°F or 10°C to reduce stretching or other un-desired effects.
3. Your new decal is designed to be installed on the exterior of your vehicle.
4. Do not store your vinyl decal in direct sunlight.

Materials Needed

- Installation squeegee (obtainable in most hardware stores)
- Masking tape
- Glass cleaner (non AMMONIA BASED) 
- Paper towel
- Measuring tape or ruler.
- Scissors or Razor

Preparation

Remove all dirt, grease and/or wax from your vehicle surface before you install your vinyl decal. This includes wax from car washes, turtle wax, rain-x, compound, etc. Your new vinyl decal will NOT adhere properly if you do not have a clean installation surface.

Caution! Do not use ammonia based cleaner. It will out gas for a couple of weeks and create bubbles under your vinyl decal.

STEP 1.

Inspect your new vinyl decal for any shipping damages. Any damage incurred during shipping must be reported to us within two business days. Using a squeegee on a table, press firmly over the whole decal assuring the pre-mask is properly stuck to the vinyl decal. Once finished, place your decal on the vehicle surface (pre-mask up and liner on surface)



STEP 2.

Place pieces of masking tape on top of the decal "pre-mask" and vehicle surface to hold the decal in place. Measure with a ruler or measuring tape to make sure your decal is properly lined up. Once in place, put a long piece of tape across the decal in the center as shown below. Remove the masking tape from one side of the decal and vehicle surface creating a hinged 'flap'. 



STEP 3.

Raise the hinged 'flap', and begin to peel the "liner" off the decal (NOT THE PRE-MASK) exposing the adhesive side of the decal. Only peel the "liner" from the decal until you reach the masking tape that crosses the whole decal.

DO NOT ALLOW THE STICKY PART OF THE DECAL TO TOUCH THE VEHICLE SURFACE.

Using scissors or a razor, cut away the peeled "liner" close to the long piece of masking tape that crosses the decal. Do not allow the scissors or razor to touch the decal as it may stick accidentally peeling the decal off the "pre-mask".



STEP 4.

Using your squeegee and starting in the middle where your masking tape crosses the decal, begin to apply the sticky side of the decal to the vehicle surface. Use horizontal strokes to apply the decal equally. Continue smoothing out the decal from top to bottom with long horizontal strokes assuring the decal is securely adhered to the vehicle surface.



STEP 5.

Place a long piece of masking tape parallel to the current piece of masking tape that crosses the decal on the decal side that you just adhered to the vehicle surface. Then remove the original long piece of masking tape that crossed the decal. This will secure the decal so you can peel off the final piece of "liner". Also remove the small corner pieces of masking tape. Slowly peel the final piece of "liner" off exposing the adhesive side of the decal. Once again do not allow the sticky part of the decal to touch the vehicle surface.



STEP 6.

Using your squeegee and starting in the middle where your masking tape crosses the decal, begin to apply the final sticky side of the decal to the vehicle surface. Use horizontal strokes to apply the decal equally. Continue smoothing out the decal from top to bottom with long horizontal strokes assuring the decal is securely adhered to the vehicle surface.



STEP 7.

Remove the final piece of masking tape. Go over the decal with the squeegee, with increasingly harder strokes assuring the decal is securely adhered to the vehicle surface. Slowly begin peeling the "pre-mask" covering the decal. Keep a close eye while removing the pre-mask making sure no part of the decal is still attached to the "pre-mask".



Final Check

Now that the "pre-mask" is removed, do a visual check assuring all the vinyl decal is adhered to the vehicle surface. More then likely you will see small air bubbles. You can make a small incision into the vinyl with a razor and use your squeegee to push the air out. Most air bubbles will disappear in a few weeks due to the heat from the sunlight. Your new vinyl decal is now installed! Please note if you live in a cold climate, be very careful using an ice scraper as it can peel the vinyl.





Pre-cautions before you start.

1. Do not install your vinyl decal in direct sunlight. It is recommended you install your vinyl decal in a garage or building.
2. Room and installation surface temperature is recommended to be 50°F or 10°C to reduce stretching or other un-desired effects.
3. Your new decal is designed to be installed on the exterior of your vehicle.
4. Do not store your vinyl decal in direct sunlight.

Materials Needed

- Installation squeegee (obtainable in most hardware stores)
- Application Fluid in Spray Bottle (Mixture of 1/2 quart (500mL) of water, 1/4 quart (250 mL) of 99% rubbing alcohol and 1 teaspoon of liquid soap)
- Glass cleaner (non AMMONIA BASED)
- Paper towel
- Measuring tape or ruler.

Preparation

Remove all dirt, grease and/or wax from your vehicle surface before you install your vinyl decal. This includes wax from car washes, turtle wax, rain-x, compound, etc. Your new vinyl decal will NOT adhere properly if you do not have a clean installation surface.

Caution! Do not use ammonia based cleaner. It will out gas for a couple of weeks and create bubbles under your vinyl decal.

 

STEP 1.

Inspect your new vinyl decal for any shipping damages. Any damage incurred during shipping must be reported to us within two business days. Using a squeegee on a table, press firmly over the whole decal assuring the pre-mask is properly stuck to the vinyl decal. Once finished, flip the decal over (pre-mask down) and slowly peel off the "liner" exposing the decals adhesive side.

DO NOT ALLOW THE STICKY PART OF THE DECAL TO TOUCH THE VEHICLE SURFACE.

Use application fluid to generously spray the vehicle surface area where your decal will be installed on. Make sure the surface area is completely sprayed down. Then generously spray application fluid onto the adhesive side of the decal.

 

 

STEP 2.

Place the decal (adhesive side down) on to the vehicle surface. While the decal is wet, you can measure and re-adjust the decal without damaging it. Once in place, go over the decal with the squeegee with firm strokes pushing the application fluid out and assuring the decal is adhering to the vehicle surface. Repeat this a few times until you remove most of the application fluid between the decal and the vehicle surface. Try not to move the decal during this step

 

 

STEP 3.

Depending on the outside temperature, wait between 30 minutes to an hour or more allowing the decal to dry and adhere securely to the vehicle surface.

 

 

STEP 4.

Once the decal is dry, start peeling off the "pre-mask" from the decal and vehicle surface. If the decal starts to peel off with the "pre-mask", re-apply decal with squeegee (Step 2), and wait about 30 minutes before attempting to remove the "pre-mask" again.

 

Final Check

Now that the "pre-mask" is removed, do a visual check assuring all the vinyl decal is adhered to the vehicle surface. More than likely you will see small air or water bubbles. You can make a small incision into the vinyl with a razor and use your squeegee to push the air or water out. Most air or water bubbles will disappear in a few weeks due to the heat from the sunlight. Allow a few days in the hot sun to allow the decal to completely cure before washing or waxing. Your new vinyl decal is now installed! Please note if you live in a cold climate, be very careful using an ice scraper as it can peel the vinyl


Decal Removal


Although vinyl decals are generally installed to be permanent, they can easily be removed. Simply heat the decal with a heat gun or hair dryer (hair dryer will take longer). Then using your fingernail, lift the edge of the decal and work across the surface of the decal. Caution! Overheating the decal will result in more difficult removal because it can actually harden to the vehicle surface.

For glass windows, many people use the same razor that removes inspection stickers to remove unwanted vinyl decals. Do not use razors on the vehicles body paint! Once the vinyl decal is removed, use PREPSOL or thinners to remove any glue residue. That is it!

Fusion Art Decals is a ShopWiki Approved Store
PayPal Logo
amazon payments

Fusion Decals is Upfront
Active Search Results
Google Sitemap Generator



Purchase of any product from FAdecals.com is not authorization for the use of any specific logo or trademark. By ordering, you convey to FAdecals.com you have authority (if need be) to use the above artwork. 

If your company logo is listed on the site but do not wish to have your logo advertised please send an email to Support@FAdecals.com and the logo will be removed.

Copyright © 2011 -    www.fadecals.com | DBA FUSION DECALS (FL) - All Rights Reserved
Compare Product Prices - http://www.prix-le-moins-cher.fr